CD4007 DATASHEET PDF

CD4007 DATASHEET PDF

Limits. Symbol. Parameter. Conditions. −40°C. +25°C. +85°C. Units. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. IL. Quiescent Device. VDD = V. Data sheet acquired from Harris Semiconductor. SCHSC – Revised September The CDUB types are supplied in lead hermetic dual-in- line. Order Number CD C National Semiconductor Corporation . This datasheet has been downloaded from: Datasheets for.

Author: JoJozilkree JoJojinn
Country: Somalia
Language: English (Spanish)
Genre: Technology
Published (Last): 23 July 2012
Pages: 289
PDF File Size: 5.30 Mb
ePub File Size: 15.39 Mb
ISBN: 894-8-30568-618-6
Downloads: 10821
Price: Free* [*Free Regsitration Required]
Uploader: Feshakar

Proceed as shown in Figure 6. What to do in the lab report Attach screen shots for working frequencies, and for too high frequencies such that transitions between 0 and VDD are not complete. Two copies with opposite phase clocks will then make a master-slave D Flip Flop.

CD4007 DATASHEET PDF DOWNLOAD

Remove all the connections to the ALD chip shown in the dashed box in Figure 3. Remember that chips 2 and 4 shown in Figure 8 need Vdd and Ground connections.

Such information will be used to improve this and future labs and your experience will help future students. Determine the VPP and dc offset setting required for function generator.

You can download or view the data sheet here or here. Therefore, this circuit is an oscillator. As a result, any change in the input D is not reflected at the output Q. For example, a single CD can be used to make a chain of 3 inverters, an inverter plus two transmission gates, or a complex logic gate. Determine the logic function implemented by the following connections to a CD Normally one would use anti-static mats and wrist straps when working with static cd datasheet electronics.

  DYNAUDIO MW160 PDF

Measure the output voltage of the second inverter and the cd datasheet at node C with the scope. You are encouraged to write down your experience with this lab along with any feedback or suggestions.

Estimate Vtp from Ids-Vgs curves. Created using Sphinx 1. Build a CMOS inverter. The other two pairs are more general purpose.

Attach screen shots for different VDD.

8. CMOS Logic Circuits — elec documentation

You may find the diagram shown below in figure 13 helpful. The CD is a very versatile IC with many uses. Thank cd datasheet for keeping our lab clean and organized.

Each pair shares a common gate pins 6,3, During the transparent phase of the latch, i. Have your GTA sign cd datasheet on each part before proceeding to the next part.

Enter search terms or a module, class or function name. A widely used circuit datashset a datasheet slave D flip flop, which we will build datasheeet cd datasheet below. In which region should it be operating when it is an open switch?

Ids-Vgs in a saturation by connection configuration, e. Construct the circuit shown in figure This is because CMOS logic requires a voltage input of 0-Vdd and the function cd datasheet always provides a waveform with a dc component of 0 V. There are 6 parts and a bonus. Measure the output voltage of the second inverter and the voltage at node C with the scope.

  COPIONE NATALE IN CASA CUPIELLO PDF

CD DATASHEET PDF DOWNLOAD

The two inverters can be built from a CD by making the following connections: Because the output of the first inverter is now zero, the capacitor will begin to discharge through R1, and the opposite side will be charged.

It is shown in the dashed box cd datasheet as chip 2 in Figure 7 above. Find the Vds at which the drain current saturates, defined as Vdsat, for all Vgs measured from the Ids-Vds curves.

Output of first inverter.

What to do in the lab report Submit all screen shots. Thank you for keeping our lab clean and organized. You should take a total of three screenshots, one each, corresponding to each inverter output.

Quick search Enter search terms or a module, class or function name. When specifying wiring between the pins of an IC, engineers often use a shorthand for connections. Navigation index next previous elec 1.

Also apply logic High to the D input. Make the connections to an rc op-amp as shown in figure 3. Attach screen shots for working frequencies, and for too high frequencies such that transitions between 0 and VDD are not complete.

Each pair shares a common gate pins 6,3, You can also document mistakes or missteps that occurred, e.