J1000 YASKAWA PDF

J1000 YASKAWA PDF

YASKAWA AC Drive-J Type: CIMR-JU. Compact V/f Control Drive. Models: V Class, Three-Phase Input: to kW. V Class, Single-Phase. YASKAWA AC Inverter Series J Document Download. The J meets all automation requirements for compact applications with variable speed operation and energy saving characteristics. A wide range of useful.

Author: Shaktizragore Tygogal
Country: El Salvador
Language: English (Spanish)
Genre: Life
Published (Last): 27 March 2006
Pages: 41
PDF File Size: 6.77 Mb
ePub File Size: 5.3 Mb
ISBN: 212-5-47026-483-8
Downloads: 16581
Price: Free* [*Free Regsitration Required]
Uploader: Vudobei

Major functions listed below. Initialization Page 78 Page 79 Page 80 – B: When operating at greater than 60 Hz the output Hz with 60 Hz base Constant output voltage will be constant. The contactor on the inrush prevention circuit yaskaaw damaged.

Improper wiring connections could cause the braking resistor to overheat and cause death or serious injury by fire. This section describes ysakawa that are commonly edited. Page Output N1000 A Magnetic contactor MC on the output side of Set up the operation sequence so that the MC is not tripped while the drive is outputting current.

If this is not appropriate for the application consider using a braking option. Got it, continue to print. Sigmaseries ac servo drive. Observing the Drive Operation The drive uses the delay time of 0. Check all the wiring after installing the drive and connecting other devices to ensure that all connections are correct.

Troubleshooting This chapter can also serve as a reference guide for tuning the drive during a trial run. This section offers helpful information for counteracting oscillation, hunting, or other faults that occur while performing a trial run.

Fluid Applications The Setup Mode saves valuable installation time by providing just the essential parameters needed to get the application running immediately.

  HERMAN WOUK WINDS OF WAR PDF

Check the frequency reference terminal input gain level assigned to terminal A1 parameter incorrect values. Precautions on installing a leakage breaker Chapter 8 Revision: If the slave address specified in the command j100 is 00H, all slaves execute the write function, but do not return response jaskawa to the master. Motor 1 Parameters E The drive is not in Drive Mode.

Verify that the rated voltage of the drive matches the voltage of the jj1000 power supply before applying power.

Also See for J Quick start manual – 38 pages Technical manual – 21 pages Quick start manual – 2 pages. Page 81 Set the frequency reference to F6. Drive Watt Loss Data Run Command Selection on page 80 details on external reference parameter selections.

Installing Peripheral Devices Disconnecting the Power Supply The drive should yxskawa shut off in the case of a fault in external equipment such as braking resistors yaksawa use of a Magnetic Contactor MC.

To print the manual completely, please, download it. Not Used Use this setting when the terminal is not used or when using the terminal as a throughput.

Current derating must be considered. Page If C is less than or equal to 6, the drive operates at Correct the parameter settings. Open the catalog to page 9. Enter text from picture: Start-up Flowchart Fine tune parameters. If even more braking torque is needed, an additional braking resistor can be connected to the built-in braking transistor. The different speed references can be selected as shown in Table 5. To prevent this problem, wait approximately 5 seconds after issuing the ENTER command before shutting off drive power.

  ATTACKING CHESS JOSH WAITZKIN PDF

The cooling fan is also designed for quick replacement: Tuning Page 87 – C2: Wiring Checklist Ensure that no frayed wires on the terminal block are touching other terminals or connections. If the drive is started with a lower reference than d, it will accelerate up to d Page Speed Agree and drive output will shut down on an oL3 fault.

The Stall Prevention level is automatically reduced in the field weakening area.

YASKAWA J1000 Technical Manual

Improper equipment sequencing could result in damage to the drive. LED digital operator by viewing the j11000 monitor parameter. The magnitude of the braking load trips the braking resistor overheat alarm, NOT the surface temperature.

Frequency reference is too low. Check the following items on a daily basis to avoid premature deterioration in performance or product failure. Drive returns to the parameter display.

J Drive – Yaskawa

Maintenance Monitor Settings This value should be reset to 0 when the relay has been replaced. Motor Capacity Rated Output Max. Mechanical Installation Failure to comply could result in damage to the drive. Table of Contents Add to my manuals Yaskaaw. Open the catalog to page 7. Motor Parameters When operating at greater than 60 Hz the output Hz with 60 Hz base Constant output voltage will be constant. No parity 0 to 2 Selection 1: